Mostrando todos los resultados 17

Brianex Bungee Connector – Bag of 10

Ideal solution for electrical and non-electric bungee cord connecting.

  • No Crimping required
  • V-Lock system for easy adjustment
  • Provides effective electrical connection
  • Bag of 10 Brianex Bungee Connectors

Cut Out Switch – Box of 10

  • Quality Strainrite Cut Out Switch
  • Simple operation & Isolation of permanent electric fences
  • On/Off status easily seen from a distance

Digital Volt Meter

  • Digital self-earthing tester for accurate kV reading
  • Reads up to 9.9kV
  • Runs on 1 x CR2032 battery

Earth Stake

Profile design for ultimate surface to ground contact
Multiwire aluminium clamp system
Overall length 2M
Width 30.4mm

Electric Fence Warning Signs – Pack Of 10

  • Double sided with indelible lettering
  • Moulded with UV stabiliser
  • In accordance with the Australian/New Zealand standards
  • Pack of 10

Fault Finder

  • Shows peak voltage, current and direction to fault in all-electric fences.
  • No second connection required.
  • Simply uses the capacitance of the user’s hand.

Flood Isolator

  • Reduces power loss when flood water contacts the electric fence line
  • Eliminates fence short outs.
  • Sealed from insect and water damage

Holeshot Staple Guide

The Holeshot is a muzzle attachment for your staple gun, which is perfectly designed to fit all Strainrite insulators for fast and effective installation on a wood post.

  • Fits the Stockade ST400i & ST400
  • Requires 2.5mm Allen key

FIN00500 Holeshot Info

KV LED Tester

  • Self-earthing fence tester with bright LED display
  • Reads up to 10kV
  • Runs on 2 x CR2016 batteries

Lightning Arrestor

  • Protects mains fence energizer from lightning
  • Channels lighting to ground to minimise damage to the energiser.

LIGHTNING Diverting Arrestor/Choke Kit

  • Proven In harsh Australian Lightning Conditions
  • Porcelain diverter
  • Joint clamps and heavy duty choke spring

Low Voltage Alarm Indicator

  • Flashes to indicate fence has dropped in voltage below 2000
  • Flashes red when Voltage below the correct level (2 settings).
  • Easily attaches to your electric fencing wire, braid or tape
  • Runs on 1 x CR2016 battery

The Strainrite Low Voltage Alarm Indicator is an invaluable ‘alarm’ for showing when there has been a drop in the voltage through the fence.

This small, lightweight unit simply clips into the fence line and the red light will flash if the voltage drops below the correct level (2 settings). It also serves to remind you, from a distance, whether the fence is on or not.

It has an off switch, and a high and low switch depending on the type of fence it is monitoring. We recommend using the low setting for any electric netting and polywire, and the high setting for others such as tape or galvanised wire.

The Low Voltage Alarm which starts flashing when the voltage drops below 2000 (As opposed to the Clip-on Indicator Flasher flashes a green light with each pulse and stops flashing when fence voltage drops below 3000 volts).

Tip: Hang it near to where the power goes into the fence. Works best on tape or rope. For Electric Netting we recommend the Indicator Light Tube

Split Bolt Wire Joining Clamp – Bag of 25

  • For use on all live earth wire connections
  • Provides a suitable electrical connection
  • For use with galvanized wire up to 2.5mm

Voltage Indicator

  • Flashes to indicate fence is operating at effective level
  • Flashes green when Voltage above 3000V
  • Easily attaches to your electric fencing wire, braid or tape
  • Runs on 1 x CR2016 battery

The Strainrite Clip-on Indicator Flasher shows the user that the fence is working.

Clip-on Indicator Flasher flashes a green light with each pulse and stops flashing when fence voltage drops below 3000 volts (as opposed to the Low Voltage Alarm which starts flashing when the voltage drops below 2000).

Very useful as optical control during darkness to indicate whether the fence is on or not. Just clip to the fence and it starts working, it does not need to be earthed. The Voltage Indicator requires a 3v Lithium battery, which is supplied already fitted.